Aluminium alloy 2011 Chemical Physical Properties Data
Aluminium 2011 is stocked by Metal Ministry Inc. In Forms of Sheets, Plates, Coils, Bar Products, Pipes & Tubular Products, Flanges, Fittings & Custom Fabrication Parts as per Client Requirements all over the world. We Offer Cut to size to Full forms of Alloy 2011 Products.
Aluminium Alloy 2011 Chemical Composition:
| % | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Bi | Pb | Others | Al |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Minimum | - | - | 5,00 | - | - | - | - | - | 0,20 | 0,20 | - | - |
| Maximum | 0,40 | 0,70 | 6,00 | - | - | - | 0,30 | - | 0,60 | 0,60 | - | rest |
Aluminium Alloy 2011 International Equivalences:
| Europe | USA | Spain | France | Germany | G.B. | Italy | Sweden | Switzerland | Japan |
| E.N. 573 | A.A. | U.N.E. | AFNOR | D.I.N. | B.S. | U.N.I. | S.I.S. | V.S.M. | J.I.S. |
| EN AW 2011 |
2011 | 38.322 L-3192 |
A-U5PbBi | AlCuBiPb 3.1655 |
FC1 | 6362 9002/5 |
4335 | AlCu6PbBi | A 2011 |
Aluminium Alloy 2011 Mechanical properties Standard: EN 755-2 Alloy: EN AW-2011A [Al 99,5]:
| Extruded bar | |||||||||
| Treatment state | Measurements mm | Rm MPa | Rp0,2 MPa | A % | A50 mm % | Hardness HB | |||
| D1) | S2) | min. | max. | min. | max. | min. | min. | ||
| T4 | ≤ 200 | ≤ 60 | 275 | – | 20 | – | 14 | 12 | 90 |
| ≤ 75 | ≤ 60 | 310 | – | 230 | – | 8 | 6 | 110 | |
| T65) | 75 < D ≤ 200 | – | 295 | – | 195 | – | 6 | – | 110 |
1) D = Diameter of circular section bars.
2) S = Distance between faces for square-section and hexagonal bars, thickness for rectangular section bars.
5) The characteristics can be obtained by means of cooling in a press.
Aluminium Alloy 2011 Physical Properties
| Modulus of elasticity N/mm2 | Specific weight g/cm3 | Melting temperature ºC | Linear expansion coefficient 1/106K | Thermal conductivity W/mK | Electrical resistivity at 20ºC - Ω cm | Electrical conductivity% IACS | Dissolution potential V |
| 72.500 | 2,84 | 540-650 | 23 | T3-152 | T3-4,4 | T3-39 |
Aluminium Alloy 2011 Technological Suitabilities
| Welding | Natural behaviour | Anodized | Mechanization State: T3 T3 T4 T6 T8 |
|---|---|---|---|
| Under flame M | In a rural environment R | For protection B | Chip fragmentation MB MB |
| At the arc under argon gas R | In an industrial environment R | Decorative M | Surface gloss B B |
| Owing to electrical resistance B R | In a marine environment B M | Hard anodized B R | |
| Brazed B M | In sea water B M |
| Thermal treatments | Products | Observations and applications | |
| Forging temperature interval: 400º-480ºC. Total annealing: 420ºC with long-term cooling up to 250ºC. Annealing against acridity: 340ºC |
Bars, profiles, tubes, flat bars. | Well-machined alloy because of their corrosion, protection anodizing is recommended. This alloy is easy to machine and you can work at high speeds with all kinds of parts under turning such as rapid-connection fittings, sleeves, flanges, washers, screws, pulleys, pistons, cylinders, tyres, plugs, bushings, threaded rods etc |
|
Aluminium Alloy 2011 Charecteristics
| Principal Design Features | This is an age-hardenable alloy noted for its free-machining characteristics and good mechanical properties. |
|---|---|
| Applications | Commonly used in the manufacture of screw machine products, machine parts, atomizer and hose parts, pipe stems, cigarette holders, and tube fittings. |
| Machinability | This is a free-machining alloy and both carbide or high-speed tool steel tooling may be used. Carbide tooling is preferred. Rake angles should be 50 degrees for top rake, 32 degree cutting edge, 15 degree side rake and 10 degree clearance. Oils should be used for heavy cutting, Light cutting may be done dry. |
| Forming | Bending, shaping and forming in general may be don with conventional tooling. Following cold working the part is usually age hardened to develop better strength properties. |
| Welding | Welding of this alloy is NOT recommended. No common methods of producing satisfactory welds have been developed. |
| Heat Treatment | Optimum strength (T8 temper) is obtained by solution heat treatment at 950 F for adequate time to insure complete heating followed by a water quench and then cold working to desired part shape and followed by a 320 F heating for 15 hours and air cool. |
| Forging | Forging, or hot working, may be accomplished in the temperature range of 550 to 900 F. |
| Hot Working | Hot working may be done at temperatures of 550 to 900 F. |
| Cold Working | This alloy is noted for its free-machining capability. It may be cold worked by all conventional means. An aging heat treatment to develop optimum strength may follow cold working. |
| Annealing | Annealing is done at 775 F by holding at that temperature for 2 to 3 hours, followed by controlled cooling at a rate of 50 F per hour down to 500 F and then air cooling. |
| Aging | Age hardening (typical for T4 temper) is done by a 950 F soak for 3 hours followed by water quench. Other temper variations are possible with additional treatment such as heating to 320 F for 14 hours, after solution heating, to produce T 8 temper. |
| Tempering | Not applicable . |
| Hardening | Age harden by 950 F heat treatment for 3 hours and water quench. See also "Aging" and "Tempering". |
| Other Physical Props | Electrical conductivity is 38% of copper. |
| Other Mechanical Props | Shear strength (ultimate) 32 ksi to T3 and 35 ksi for T8 |
Countries we Export
Metal Ministry Inc Exports Commercially Pure Aluminium EN AW-2011 UNS A92011 to United States of America, Russia, United Kingdom, Kuwait, Qatar, Oman, UAE, Nigeria, Ethiopia, Egypt, Tanzania, Uganda, Algeria, Sudan, Morocco, Angola, Mozambique, Ghana, Cameroon, Cote D`lvoire, Niger, Burkina Faso, Mali, Malawi, Zambia, Senegal, Chad, Somalia, Zimbabwe, Guinea, Rwanda, Benin, Brundi, Tunisia, South Sudan, Togo, Sierra Leone, Libya, Congo, Liberia, Central African Republic, Mauritania, Eritrea, Namibia, Gambia, Botswana, Gabon, Lesotho, Guinea-Bissau, Mauritius, Eswatini, Djibouti, Comoros, Cabo Verde, Seychelles, Reunion, Western Sahara, Mayotte, Saint Helena, Afghanistan, Armenia, Azerbaijan, Bahrain, Bangladesh, Bhutan, Brunei, Cambodia, Cyprus, East Timor, Georgia, Indonesia, Iran, Iraq, Israel, Japan, Kazakhstan, Jordan, Kyrgyzstan, Lebanon, Malaysia, Maldives, Mongolia, Myanmar, Nepal, North Korea, Palestine, Philippines, Saudi Arabia, Singapore, South Korea, Sri Lanka, Syria, Tajikistan, Thailand, Turkey, Taiwan, Uzbekistan, Vietnam, Yemen, Albania, Andorra, Austria, Belarus, Belgium, Bosnia & Herzegovina, Bulgaria, Croatia, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Lithuania, Moldova, Monaco, Montenegro, Norway, Netherlands, Poland, Portugal, Romania, Russia, San Marino, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Ukraine, Vatican City, Antigua & Barbuda, Anguilla, The Bahamas, Barbados, British Virgin Island, Canada, Cayman Island, Costa Rica, Cuba, Dominica, Greenland, Haiti, Jamaica, Martinique, Mexico, Navassa Island, Panama, Puerto Rico, Saint Lucia, Trinidad & Tobago, Argentina, Brazil, Bolivia, Chile, Ecuador, Colombia, Guyana, Paraguay, Peru, Uruguay, Venezuela, Australia, Fiji, Marshall Island, New Zealand, Papua New Guinea, Samoa, Solomon Islands & Tuvalu.
Cities we Supply
Metal Ministry Inc Supplies Commercially Pure Aluminium EN AW-2011 UNS A92011 products to Agartala, Agra, Agra Rampur, Ahmedabad, Aizawl, Ajmer, Aligarh, Allahabad, Alwar, Amaravati, Ambala, Ambattur, Ambernath, Amravati, Amritsar, Aurangabad, Bangalore, Bareilly, Belgaum, Bhagalpur, Bhavnagar, Bhilai, Bhiwandi, Bhopal, Bhubaneswar, Bidhannagar, Biharsharif, Bikaner, Bilaspur, Bokaro, Chandigarh, Chennai, Chittoor, Coimbatore, Cuttack, Dahod, Davanegere, Dehradun, Delhi, Dhanbad, Dharamsala, Dindigul, Diu, Durgapur, Erode, Faridabad, Fatehpur, Gandhidham, Gandhinagar, Ghaziabad, Greater Hyderabad, Greater Mumbai, Greater Warangal, Gurgaon, Guwahati, Gwalior, Haldia, Howrah, Hubballi-Dharwad, Hyderabad, Imphal, Indore, Jabalpur, Jaipur, Jalandhar, Jammu, Jamnagar, Jamshedpur, Jhansi, Jodhpur, Junagadh, Kakinada, Kalyan-Dombivali, Kanpur, Karnal, Kavaratti, Kochi, Kohima , Kolhapur, Kolkata, Kota , Lucknow, Ludhiana, Madurai , Mehsana, Mangalore, Mangaluru, Mira-Bhayandar, Moradabad, Morbi, Mumbai, Muzaffarpur, Mysore, Nagpur, Namchi, Nasik, Navi Mumbai, NDMC, Nellore, New Delhi, New Town Kolkata, Noida, Oulgaret, Pali, Panaji, Panipat, Panvel, Pasighat, Patiala, Patna, Pimpri-Chinchwad, Port Blair, Puducherry, Pune, Raipur, Rajkot, Raipur, Raurkela Industrial Township, Rourkela, Sagar, Salem, Satna, Secunderabad, Shaharanpur, Shillong, Siliguri, Silvassa, Solapur, Srinagar, Surat, Thane, Thanjavur, Thiruvananthapuram, Thoothukudi, Thrissur, Tiruchirapalli, Tirunelveli, Tirupur, Tumkur, Udaipur, Ujjain, Ulhasnagar, Vadodara, Vapi, Varanasi, Vasai-Vasai-Virar, Vellore, Vishakhapatnam.
To buy online, Or get price of Commercially Pure Aluminium EN AW-2011 UNS A92011 send us an email on enquiry@metalministry.in or Call/WhatsApp on +91-9892171042 for quick quote & response. Aluminium EN AW-2011 UNS A92011 are supplied in Relevant standards as per customer requirements & Mill TC from Indian, USA, South African, Russian, German & European Mills only.
