Aluminium alloy 1060 Chemical Physical Properties Data
Aluminium 1060 is stocked by Metal Ministry Inc. In Forms of Sheets, Plates, Coils, Bar Products, Pipes & Tubular Products, Flanges, Fittings & Custom Fabrication Parts as per Client Requirements all over the world. We Offer Cut to size to Full forms of Alloy 1060 Products.
Aluminium Alloy 1060 Component Elements Properties:
Component Elements Properties | Metric | English | Comments |
---|---|---|---|
Aluminum, Al | >= 99.60 % | >= 99.60 % | Specified |
Copper, Cu | <= 0.05 % | <= 0.05 % | |
Iron, Fe | <= 0.35 % | <= 0.35 % | |
Magnesium, Mg | <= 0.03 % | <= 0.03 % | |
Manganese, Mn | <= 0.03 % | <= 0.03 % | |
Other, each | <= 0.03 % | <= 0.03 % | |
Silicon, Si | <= 0.25 % | <= 0.25 % | |
Titanium, Ti | <= 0.03 % | <= 0.03 % | |
Vanadium, V | <= 0.05 % | <= 0.05 % | |
Zinc, Zn | <= 0.05 % | <= 0.05 % |
Aluminium Alloy 1060 Physical Composition:
Physical Properties | Metric | English | Comments |
---|---|---|---|
Density | 2.705 g/cc | 0.09772 lb/in³ | AA; Typical |
Aluminium Alloy 1060 Mechanical Properties:
Mechanical Properties | Metric | English | Comments |
---|---|---|---|
Hardness, Brinell | 19 | 19 | AA; Typical; 500 g load; 10 mm ball |
Tensile Strength, Ultimate | 68.9 MPa | 10000 psi | AA; Typical |
55.0 - 95.0 MPa | 7980 - 13800 psi | Sheet and plate | |
>= 58.0 MPa @Thickness 0.254 - 12.7 mm |
>= 8410 psi @Thickness 0.0100 - 0.500 in |
Drawn tube | |
58.0 - 95.0 MPa @Thickness 1.27 - 4.29 mm |
8410 - 13800 psi @Thickness 0.0500 - 0.169 in |
Extruded tube | |
Tensile Strength, Yield | >= 17.0 MPa | >= 2470 psi | Sheet and plate |
>= >17.0 MPa | >= 2470 psi | Extruded tube | |
27.6 MPa | 4000 psi | AA; Typical | |
>= 17.0 MPa @Thickness 0.254 - 12.7 mm |
>= 2470 psi @Thickness 0.0100 - 0.500 in |
Drawn tube | |
Elongation at Break | 15 - 25 % | 15 - 25 % | Sheet and plate |
43 % @Thickness 1.59 mm |
43 % @Thickness 0.0625 in |
AA; Typical | |
Modulus of Elasticity | 68.9 GPa | 10000 ksi | AA; Typical; Average of tension and compression. Compression modulus is about 2% greater than tensile modulus. |
Ultimate Bearing Strength | 117 MPa | 17000 psi | Edge distance/pin diameter = 2.0 |
Bearing Yield Strength | 41.0 MPa | 5950 psi | Edge distance/pin diameter = 2.0 |
Poissons Ratio | 0.33 | 0.33 | |
Fatigue Strength | 20.7 MPa @# of Cycles 5.00e+8 |
3000 psi @# of Cycles 5.00e+8 |
completely reversed stress; RR Moore machine/specimen |
Machinability | 10 % | 10 % | 0-100 Scale of Aluminum Alloys |
Shear Modulus | 26.0 GPa | 3770 ksi | Calculated |
Shear Strength | 48.3 MPa | 7000 psi | AA; Typical |
Aluminium Alloy 1060 Electrical Properties:
Electrical Properties | Metric | English | Comments |
---|---|---|---|
Electrical Resistivity | 0.00000283 ohm-cm @Temperature 20.0 °C |
0.00000283 ohm-cm @Temperature 68.0 °F |
AA; Typical |
Aluminium Alloy 1060 Thermal Properties:
Thermal Properties | Metric | English | Comments |
---|---|---|---|
Heat of Fusion | 390 J/g | 168 BTU/lb | |
CTE, linear | 21.8 µm/m-°C @Temperature -50.0 - 20.0 °C |
12.1 µin/in-°F @Temperature -58.0 - 68.0 °F |
|
23.6 µm/m-°C @Temperature 20.0 - 100 °C |
13.1 µin/in-°F @Temperature 68.0 - 212 °F |
AA; Typical; average over range | |
24.5 µm/m-°C @Temperature 20.0 - 200 °C |
13.6 µin/in-°F @Temperature 68.0 - 392 °F |
||
25.5 µm/m-°C @Temperature 20.0 - 300 °C |
14.2 µin/in-°F @Temperature 68.0 - 572 °F |
||
25.5 µm/m-°C @Temperature 20.0 - 300 °C |
14.2 µin/in-°F @Temperature 68.0 - 572 °F |
average | |
Specific Heat Capacity | 0.900 J/g-°C | >0.215 BTU/lb-°F | |
Thermal Conductivity | 234.2 W/m-K | 1625 BTU-in/hr-ft²-°F | AA; Typical at 77°F |
Melting Point | 657.2 °C | 1215 °F | AA; Typical range based on typical composition for wrought products >= 1/4 in. thickness |
Solidus | 646.1 °C | 1195 °F | AA; Typical |
Liquidus | 657.2 °C | 1215 °F | AA; Typical |
Aluminium Alloy 1060 Processing Properties:
Processing Properties | Metric | English | Comments |
---|---|---|---|
Annealing Temperature | 343 °C | 650 °F | |
Aluminium Alloy 1060 Characteristics:
Principal Design Features | This is a relatively low strength, essentially pure aluminum, alloy. It is noted for excellent welding characteristics and formability along with good corrosion resistance. It cannot be hardened by heat treatment. |
Applications | Commonly used in the manufacture of chemical equipment and railroad tank cars. |
Machinability | The machinability of AL 1060 is fair to poor, especially in the soft temper conditions. In the harder (cold worked) tempers such as H16 and H18 the machining characteristics are improved. Either carbide or high-speed steel tooling may be used and use of lubricants is recommended, although some cutting may be done dry. |
Forming | This alloy has excellent forming capability by cold or hot working with commercial techniques. |
Welding | AL 1060 may be welded by standard commercial methods. If filler rod is required it should be of AL 1060. A precaution should be noted for the use of resistance welding as by this method some trial and error experimentation may be required to obtain good results. |
Heat Treatment | This alloy does not harden by heat treatment. It may be annealed after cold working. See "Annealing". |
Forging | This alloy may be forged in the temperature range of 950 to 700 F. |
Hot Working | Hot working, if required, may be done in the range of 900 to 500 F. |
Cold Working | The cold working characteristics of AL 1060 are excellent. It can readily be cold worked by all conventional methods. |
Annealing | Annealing may be done at 650 F followed by air cooling. |
Aging | Not applicable to this alloy. |
Tempering | Not applicable. |
Hardening | The alloy hardens only from cold working. Tempers H12, H14, H16, H18 are determined by the amount of cold working imparted into the alloy. |
Other Physical Props | Electrical conductivity 55% of copper. |
Other Mechanical Props | Shear strength of annealed (O temper) is 7 ksi. For H14 temper it is 9 ksi and for H18 temper 11 ksi. |
Principal Design Features | This is a relatively low strength, essentially pure aluminum, alloy. It is noted for excellent welding characteristics and formability along with good corrosion resistance. It cannot be hardened by heat treatment. |
Applications | Commonly used in the manufacture of chemical equipment and railroad tank cars. |
Machinability | The machinability of AL 1060 is fair to poor, especially in the soft temper conditions. In the harder (cold worked) tempers such as H16 and H18 the machining characteristics are improved. Either carbide or high-speed steel tooling may be used and use of lubricants is recommended, although some cutting may be done dry. |
Forming | This alloy has excellent forming capability by cold or hot working with commercial techniques. |
Welding | AL 1060 may be welded by standard commercial methods. If filler rod is required it should be of AL 1060. A precaution should be noted for the use of resistance welding as by this method some trial and error experimentation may be required to obtain good results. |
Heat Treatment | This alloy does not harden by heat treatment. It may be annealed after cold working. See "Annealing". |
Forging | This alloy may be forged in the temperature range of 950 to 700 F. |
Hot Working | Hot working, if required, may be done in the range of 900 to 500 F. |
Cold Working | The cold working characteristics of AL 1060 are excellent. It can readily be cold worked by all conventional methods. |
Annealing | Annealing may be done at 650 F followed by air cooling. |
Aging | Not applicable to this alloy. |
Tempering | Not applicable. |
Hardening | The alloy hardens only from cold working. Tempers H12, H14, H16, H18 are determined by the amount of cold working imparted into the alloy. |
Other Physical Props | Electrical conductivity 55% of copper. |
Other Mechanical Props | Shear strength of annealed (O temper) is 7 ksi. For H14 temper it is 9 ksi and for H18 temper 11 ksi. |
Countries we Export
Metal Ministry Inc Exports Commercially Pure Aluminium EN AW-1060A UNS A91060 to United States of America, Russia, United Kingdom, Kuwait, Qatar, Oman, UAE, Nigeria, Ethiopia, Egypt, Tanzania, Uganda, Algeria, Sudan, Morocco, Angola, Mozambique, Ghana, Cameroon, Cote D`lvoire, Niger, Burkina Faso, Mali, Malawi, Zambia, Senegal, Chad, Somalia, Zimbabwe, Guinea, Rwanda, Benin, Brundi, Tunisia, South Sudan, Togo, Sierra Leone, Libya, Congo, Liberia, Central African Republic, Mauritania, Eritrea, Namibia, Gambia, Botswana, Gabon, Lesotho, Guinea-Bissau, Mauritius, Eswatini, Djibouti, Comoros, Cabo Verde, Seychelles, Reunion, Western Sahara, Mayotte, Saint Helena, Afghanistan, Armenia, Azerbaijan, Bahrain, Bangladesh, Bhutan, Brunei, Cambodia, Cyprus, East Timor, Georgia, Indonesia, Iran, Iraq, Israel, Japan, Kazakhstan, Jordan, Kyrgyzstan, Lebanon, Malaysia, Maldives, Mongolia, Myanmar, Nepal, North Korea, Palestine, Philippines, Saudi Arabia, Singapore, South Korea, Sri Lanka, Syria, Tajikistan, Thailand, Turkey, Taiwan, Uzbekistan, Vietnam, Yemen, Albania, Andorra, Austria, Belarus, Belgium, Bosnia & Herzegovina, Bulgaria, Croatia, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Lithuania, Moldova, Monaco, Montenegro, Norway, Netherlands, Poland, Portugal, Romania, Russia, San Marino, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Ukraine, Vatican City, Antigua & Barbuda, Anguilla, The Bahamas, Barbados, British Virgin Island, Canada, Cayman Island, Costa Rica, Cuba, Dominica, Greenland, Haiti, Jamaica, Martinique, Mexico, Navassa Island, Panama, Puerto Rico, Saint Lucia, Trinidad & Tobago, Argentina, Brazil, Bolivia, Chile, Ecuador, Colombia, Guyana, Paraguay, Peru, Uruguay, Venezuela, Australia, Fiji, Marshall Island, New Zealand, Papua New Guinea, Samoa, Solomon Islands & Tuvalu.
Cities we Supply
Metal Ministry Inc Supplies Commercially Pure Aluminium EN AW-1060A UNS A91060 products to Agartala, Agra, Agra Rampur, Ahmedabad, Aizawl, Ajmer, Aligarh, Allahabad, Alwar, Amaravati, Ambala, Ambattur, Ambernath, Amravati, Amritsar, Aurangabad, Bangalore, Bareilly, Belgaum, Bhagalpur, Bhavnagar, Bhilai , Bhiwandi, Bhopal, Bhubaneswar, Bidhannagar, Biharsharif, Bikaner, Bilaspur, Bokaro, Chandigarh, Chennai, Chittoor, Coimbatore, Cuttack, Dahod, Davanegere, Dehradun, Delhi, Dhanbad, Dharamsala, Dindigul, Diu, Durgapur, Erode, Faridabad, Fatehpur, Gandhidham, Gandhinagar, Ghaziabad, Greater Hyderabad, Greater Mumbai, Greater Warangal, Gurgaon, Guwahati, Gwalior, Haldia, Howrah, Hubballi-Dharwad, Hyderabad, Imphal, Indore, Jabalpur, Jaipur, Jalandhar, Jammu, Jamnagar, Jamshedpur, Jhansi, Jodhpur, Junagadh, Kakinada, Kalyan-Dombivali, Kanpur, Karnal, Kavaratti, Kochi, Kohima , Kolhapur, Kolkata, Kota , Lucknow, Ludhiana, Madurai , Mehsana, Mangalore, Mangaluru, Mira-Bhayandar, Moradabad, Morbi, Mumbai, Muzaffarpur, Mysore, Nagpur, Namchi, Nasik, Navi Mumbai, NDMC, Nellore, New Delhi, New Town Kolkata, Noida, Oulgaret, Pali, Panaji, Panipat, Panvel, Pasighat, Patiala, Patna, Pimpri-Chinchwad, Port Blair, Puducherry, Pune, Raipur, Rajkot, Raipur, Raurkela Industrial Township, Rourkela, Sagar, Salem, Satna, Secunderabad, Shaharanpur, Shillong, Siliguri, Silvassa, Solapur, Srinagar, Surat, Thane, Thanjavur, Thiruvananthapuram, Thoothukudi, Thrissur, Tiruchirapalli, Tirunelveli, Tirupur, Tumkur, Udaipur, Ujjain, Ulhasnagar, Vadodara, Vapi, Varanasi, Vasai-Virar, Vellore, Vishakhapatnam.
To buy online, Or get price of Commercially Pure Aluminium EN AW-1060A UNS A91060 send us an email on enquiry@metalministry.in or Call/WhatsApp on +91-9892171042 for quick quote & response. Aluminium EN AW-1060A UNS A91060 are supplied in Relevant standards as per customer requirements & Mill TC from Indian, USA, South African, Russian, German & European Mills only.